MARSHMALLOW GRILL RECIPES

Steps:

• Using a very sharp knife, trim the fat on the fatty side of the brisket so it is a scant 1/4 inch thick, making sure it is no thinner than that. On the meatier side, remove the web-like membrane so the coarsely grained meat underneath is visible. Make sure to cut away and discard any hard clumps of fat on both sides of the brisket.
• In a small bowl stir together the salt and pepper. Coat the entire surface of the brisket evenly with the seasoning. Put the brisket on a plate and refrigerate until ready to smoke (you can do this up to 12 hours in advance).
• Prepare the water smoker for indirect cooking over very low heat (200° to 250°F). Brush the top cooking grate clean.
• Spray the brisket on both sides with water to wet the surface. Add 3 or 4 large mesquite and/or oak chunks to the smoker. When smoke appears, place the brisket, fat side down, on the top cooking grate, and cook over indirect very low heat, with the lid closed, until a nice dark crust forms on the surface, about 4 to 5 hours, adding the remaining wood chunks to the smoker after the first hour. The surface color of the brisket is important as it indicates you have created a good “bark” and the brisket will no longer absorb much smoke. While color is the primary indication, you should also check the internal temperature of the brisket with an instant-read thermometer inserted in the thickest part; it should register between 150° and 160°F.
• Remove the brisket from the smoker and spray it again on both sides with water. Spray a large sheet of parchment paper with water to dampen it, then wrap the brisket in the parchment, covering it completely. Now wrap the brisket in heavy-duty aluminum foil, again enclosing it completely.
• Place the wrapped brisket, fat side down, on the top cooking grate and continue cooking over indirect very low heat, with the lid closed, until an instant-read thermometer inserted into the thickest part of the brisket registers 200° to 203°F and the meat is so tender than when you press it with your fingers through the foil it feels like a giant marshmallow, 5 to 7 hours or longer. Tenderness is a more important indicator of doneness than temperature, as timing can vary according to the beef breed and characteristics of the meat.
• Transfer the brisket, still wrapped in parchment and foil, to a dry, insulated cooler, close the lid, and let the meat rest for 2 to 4 hours.
• Unwrap the brisket and place it on a cutting board, being careful to keep the precious juices trapped in the wrappings. Pour the barbecue sauce into a medium saucepan and warm over medium heat on the stove until hot, about 5 minutes.
• While the sauce heats, cut the brisket across the grain into thin slices. Serve the slices with as much or as little of the sauce as you like. You can either drizzle the reserved meat juices over the slices or add them to the sauce. If the meat from the flat portion of the brisket is a little dry, coarsely chop it and mix it with as much sauce as you like.
• Serve the brisket warm on the buns.

Steps:

• 1. Using a very sharp knife, trim the fat on the fatty side of the brisket so that it is about 5 mm thick, but no less. On the meatier side, remove the web-like membrane so that the coarsely grained meat underneath is visible. Make sure to remove any hard clumps of fat on either side of the brisket.
• 2. Mix the salt and pepper, and then rub the brisket evenly on both sides with the seasoning. Put the brisket in the fridge until you’re ready to cook.
• 3. Prepare the barbecue for indirect cooking at very low heat (110° C). (Refer to our smoking guide for advise on how to set up)
• 4. Spray the brisket on both sides with water to make the surface wet. Add half of the wood chunks to the barbecue. When smoke appears, place the brisket, fat side down, on the top cooking grate, close the lid, and cook over indirect, very low heat until it has a nice dark crust on the surface, i.e. for about 4 hours. After the first hour, add the remaining wood chunks to the barbecue. The surface colour of the meat indicates that you have created a good ‘bark’, and that the brisket will no longer absorb much smoke, so it is time to wrap it up. While colour is the primary indication, you should also check the internal temperature of the meat at this point. It should be somewhere between 65 and 70° C in the thickest part of the meat.
• 5. Remove the brisket from the barbecue, and spray it on both sides with water. Then wrap the brisket in damp baking paper before tightly wrapping it in heavy-duty aluminium foil.
• 6. Place the wrapped brisket, fat side down, on the top grate of the barbecue and continue cooking over indirect very low heat, with the lid closed, until the meat is so tender that when you press it with your fingers through the foil, it feels like a giant marshmallow and the internal temperature is 90–95° C, i.e. for 2 to 4 hours or more (tenderness is a more important indicator of doneness than temperature). The amount of time required will depend on the particular breed of cattle and other characteristics of the meat.
• 7. Transfer the brisket, still wrapped in foil, to a dry, insulated coolbox. Close the lid and let the meat rest for 2 to 4 hours.
• 8. Unwrap the brisket and place it on a cutting board, being careful to keep the precious meat juices in the foil.
• 9. Warm the barbecue sauce over a medium heat on the stove for about 5 minutes. Cut the brisket across the grain into thin slices, and serve with as much or as little sauce as you like. If desired, add the meat juices to the sauce. If the meat from the flat is a little dry, coarsely chop it and mix with as much sauce as you like.
• 10. Serve warm on buns, or with a side of coleslaw or barbecued beans, for a typical Texan treat!