GRILL SPRAY RECIPES

Steps:

• Preheat a pellet grill to 275 degrees F (see Cook's Note). Combine 2 tablespoons salt, 4 tablespoons coarsely ground pepper and 2 teaspoons paprika in a small bowl. Rub each rack of ribs all over with 1 tablespoon oil and sprinkle evenly with the salt and spice mixture on both sides.
• Transfer the ribs, meat-side up, to the grill grates. Cover the grill and cook for 1 hour.
• Meanwhile, combine 1/3 cup cider vinegar with 1/3 cup water in a spray bottle. After 1 hour spray the ribs with the vinegar-water mixture so they are damp all over. Cover and cook for 1 more hour.
• Meanwhile, combine the ketchup, 3/4 cup water, the remaining 1/3 cup cider vinegar, white vinegar, brown sugar, Worcestershire sauce, 2 teaspoons salt, 2 teaspoons pepper, hot sauce and the remaining 2 teaspoons paprika in a medium saucepan. Cook over medium heat until the mixture is warmed through and the sugar is melted, about 2 minutes. Set aside.
• Check the ribs and spray them again with vinegar-water. They should be starting to take on a red color from the smoke. Cover and cook until they are deep red, 30 to 45 minutes. Spray the ribs once more, then brush the meaty part of each rack with 1/4 cup of the sauce. Close the grill and cook for another 15 minutes so the sauce can set.
• Lay down two pieces of heavy-duty foil that are long enough to enclose each rack on a work surface and spread half of each sheet with 1/4 cup sauce. Transfer the rib racks, meat side down, onto the saucy part of the foil. Coat the bone sides with 1/4 cup sauce and a few sprays of the vinegar-water, then fold the foil over and seal tightly.
• Add another layer of foil if the first has punctured during wrapping. Transfer the ribs to a rimmed baking sheet and place on the grill (the baking sheet will catch any juices that leak out). Cover and cook until tender but not falling off the bone, about 2 hours.
• Remove from the grill and let rest 5 minutes before carefully unwrapping (watch out for hot steam). Slice each rack into individual rib portions and serve with the remaining sauce.

Steps:

• Using a very sharp knife, trim the fat on the fatty side of the brisket so it is a scant 1/4 inch thick, making sure it is no thinner than that. On the meatier side, remove the web-like membrane so the coarsely grained meat underneath is visible. Make sure to cut away and discard any hard clumps of fat on both sides of the brisket.
• In a small bowl stir together the salt and pepper. Coat the entire surface of the brisket evenly with the seasoning. Put the brisket on a plate and refrigerate until ready to smoke (you can do this up to 12 hours in advance).
• Prepare the water smoker for indirect cooking over very low heat (200° to 250°F). Brush the top cooking grate clean.
• Spray the brisket on both sides with water to wet the surface. Add 3 or 4 large mesquite and/or oak chunks to the smoker. When smoke appears, place the brisket, fat side down, on the top cooking grate, and cook over indirect very low heat, with the lid closed, until a nice dark crust forms on the surface, about 4 to 5 hours, adding the remaining wood chunks to the smoker after the first hour. The surface color of the brisket is important as it indicates you have created a good “bark” and the brisket will no longer absorb much smoke. While color is the primary indication, you should also check the internal temperature of the brisket with an instant-read thermometer inserted in the thickest part; it should register between 150° and 160°F.
• Remove the brisket from the smoker and spray it again on both sides with water. Spray a large sheet of parchment paper with water to dampen it, then wrap the brisket in the parchment, covering it completely. Now wrap the brisket in heavy-duty aluminum foil, again enclosing it completely.
• Place the wrapped brisket, fat side down, on the top cooking grate and continue cooking over indirect very low heat, with the lid closed, until an instant-read thermometer inserted into the thickest part of the brisket registers 200° to 203°F and the meat is so tender than when you press it with your fingers through the foil it feels like a giant marshmallow, 5 to 7 hours or longer. Tenderness is a more important indicator of doneness than temperature, as timing can vary according to the beef breed and characteristics of the meat.
• Transfer the brisket, still wrapped in parchment and foil, to a dry, insulated cooler, close the lid, and let the meat rest for 2 to 4 hours.
• Unwrap the brisket and place it on a cutting board, being careful to keep the precious juices trapped in the wrappings. Pour the barbecue sauce into a medium saucepan and warm over medium heat on the stove until hot, about 5 minutes.
• While the sauce heats, cut the brisket across the grain into thin slices. Serve the slices with as much or as little of the sauce as you like. You can either drizzle the reserved meat juices over the slices or add them to the sauce. If the meat from the flat portion of the brisket is a little dry, coarsely chop it and mix it with as much sauce as you like.
• Serve the brisket warm on the buns.